Claus process

 ( Desulfurization ) 

The Claus process is a Desulfurisation process, recovering elemental sulfur from gaseous mixtures containing hydrogen sulfide, (H₂S). First patented in 1883 by the chemist Carl Friedrich Claus, the Claus process remains the most important desulfurization process in the Petrochemical industry. It is standard at Oil refinery, natural gas processing plants, and gasification or Syngas. In 2005, byproduct sulfur from hydrocarbon-processing facilities constituted the vast majority of the 64 teragrams of sulfur produced worldwide. Sulfur production report by the United States Geological Survey Discussion of recovered byproduct sulfur Der Claus-Prozess. Reich an Jahren und bedeutender denn je, Bernhard Schreiner, Chemie in Unserer Zeit 2008, Vol. 42, Issue 6, Pages 378–392.

The overall Claus process reaction is described by the following equation:

2 H₂S + O₂ → 2 S + 2 H₂O

However, the process occurs in two steps:

2 H₂S + 3 O₂ → 2 SO₂ + 2 H₂O

4 H₂S + 2 SO₂ → 3 S₂ + 4 H₂O

Moreover, the input feedstock is usually a mixture of gases, containing hydrogen cyanide, , sulfur dioxide or ammonia. The mixture may begin as raw natural gas, or output from physical and chemical gas treatment units (Selexol, Rectisol, Purisol and amine scrubbers) when e.g. refining crude oil.

(1984). 9780824771508, Marcel Dekker, Inc.. ISBN 9780824771508

Gases containing over 25% H₂S are suitable for the recovery of sulfur in straight-through Claus plants. Gases with less than 25% H₂S can be processed through alternate configurations such as a split flow, or feed and air preheating.Gas Processors Association Data Book, 10th Edition, Volume II, Section 22

---

History The process was invented by Carl Friedrich Claus, a German chemist working in England. A British patent was issued to him in 1883. The process was later significantly modified by IG Farben. Bibliographic Citation Sulfur Recovery Technology, B.G. Goar, American Institute of Chemical Engineers Spring National Meeting, New Orleans, Louisiana, April 6, 1986

---

Process description A schematic process flow diagram of a basic 2+1-reactor (converter) SuperClaus unit is shown below: The Claus technology can be divided into two process steps, thermal and catalyst.

---

Thermal step In the thermal step, hydrogen sulfide-laden gas burns in a substoichiometric combustion at temperatures above 850 °C.Or between 950 and 1200 °C and even hotter near the flame, as stated in Der Claus-Prozess. Reich an Jahren und bedeutender denn je, Bernhard Schreiner, Chemie in Unserer Zeit 2008, Vol. 42, Issue 6, Pages 378–392. The process requires careful control of the fuel-air ratio. To ensure a stoichiometric Claus reaction in the catalytic step, only of the hydrogen sulfide (H₂S) content should convert to SO₂.

A Claus facility usually maintains several separate fires in lances surrounding a central muffle to handle different gas sources. The concentration of H₂S and other combustible components ( or ammonia) then determine how the feed gas is burned.

Claus gases with no further combustible contents besides H₂S (acid gas) burn in the lances by the following chemical reaction:

2 H₂S + 3 O₂ → 2 SO₂ + 2 H₂O       (Δ H = −518 kJ mol⁻¹)

This is a strongly exothermic, free-flame oxidation of hydrogen sulfide, generating sulfur dioxide.

The central muffle itself burns gas mixtures containing ammonia (from a refinery's sour water stripper) or hydrocarbons. Sufficient air is injected into the muffle for the complete combustion of all hydrocarbons and ammonia, and the temperature is often maintained above 1050°C.Klint, B. "Hydrocarbon Destruction in the Claus SRU Reaction Furnace." Proceedings of the Laurance Reid Gas Conditioning Conference. 2000.Rahman, Ramees K., et al. "Reduction in natural gas consumption in sulfur recovery units through kinetic simulation using a detailed reaction mechanism." Industrial & Engineering Chemistry Research (2018). The high temperature destroys BTEX (Benzene, Toluene, Ethylbenzene and Xylene) mixtures, which otherwise would poison the downstream Claus catalyst.Rahman, Ramees K., Salisu Ibrahim, and Abhijeet Raj. "Oxidative destruction of monocyclic and polycyclic aromatic hydrocarbon (PAH) contaminants in sulfur recovery units." Chemical Engineering Science 155 (2016): 348–365.

To reduce the process gas volume or obtain higher combustion temperatures, the air requirement can also be covered by injecting oxygen. Several technologies utilizing oxygen enrichment are available in industry, but require a special burner in the reaction furnace.

The Claus reaction continues downstream, as more hydrogen sulfide (hydrogen sulfide) reacts with the sulfur dioxide, to produce gaseous, elemental sulfur:

2 H₂S + SO₂ → 3 S + 2 H₂O      (Δ H = −1165.6 kJ mol⁻¹)

The sulfur forms in the thermal phase as highly reactive S₂ diradicals which combine exclusively to the S₈ allotrope:

4 S₂ → S₈

Usually, 60 to 70% of the total amount of sulfur produced in the process is already present at the conclusion of the thermal process step.

---

Side reactions Other chemical processes taking place in the thermal step of the Claus reaction are:

• The formation of hydrogen gas:

:2 H₂S → S₂ + 2 H₂        (Δ H > 0)

: CH₄ + 2 H₂O → CO₂ + 4 H₂

• The formation of carbonyl sulfide:

: H₂S + CO₂ → S=C=O + H₂O

• The formation of carbon disulfide:

: CH₄ + 2 S₂ → S=C=S + 2 H₂S

---

Catalytic step

The waste stream from the thermal step is initially cooled to precipitate the sulfur, similar to the post-catalytic cooling discussed below. Further treatment with an activated aluminum oxide or Titanium dioxide oxide Catalysis then boosts the sulfur yield. One suggested mechanism is that S₆ and S₈ desorb from the catalyst's active sites with simultaneous formation of stable cyclic elemental sulfur.

Catalytic treatment is normally repeated a maximum of three times. Where an incineration or tail-gas treatment unit (TGTU) is added downstream of the Claus plant, only two catalytic stages are usually installed.

The catalytic recovery of sulfur consists of three substeps: heating, catalytic reaction and cooling plus condensation. Reheating the gas prevents sulfur condensation in the catalyst bed, which fouls the catalyst. Several industrial methods achieve the required bed operating temperature:

• Hot-gas bypass: mixing in bypass gas direct from the waste-heat boiler.
• Indirect steam reheaters: a heat exchanger consuming high-pressure steam.
• Gas/gas exchangers: a heat exchanger cooling the hot gas from an upstream catalytic reactor.
• Direct-fired heaters: fired reheaters burning acid gas or fuel gas substoichiometrically to prevent oxygen breakthrough

The typically recommended operating temperature of the first catalyst stage is 315 °C to 330 °C (bottom bed temperature). The high temperature hydrolyzes carbonyl sulfide and Carbon disulfide, combustion byproducts that are otherwise inert during the modified Claus process. For subsequent stages, the catalytic conversion is maximized at lower temperatures, but care must be taken to remain above sulfur's dew point. The operating temperatures of the subsequent catalytic stages are typically 240 °C for the second stage and 200 °C for the third stage (bottom bed temperatures).

After each catalytic pass, the process gas cools in the sulfur condenser to between 150 and 130 °C, whereupon the sulfur formed condenses. The waste heat and the condensation heat are captured as medium or low-pressure steam. The condensed sulfur is removed through a liquid outlet.

Before storage, liquid sulfur streams pass a degassing unit, which removes gases (primarily H₂S) dissolved in the sulfur.

The tail gas from the Claus process still contains combustible components and sulfur compounds (H₂S, H₂ and CO). It either burns in an incineration unit or is further desulfurized in a downstream tail gas treatment unit.

---

Sub dew point Claus process

The conventional Claus process described above is limited in its conversion due to the reaction equilibrium being reached. Like all exothermic reactions, greater conversion can be achieved at lower temperatures, however as mentioned the Claus reactor must be operated above the sulfur dew point (120–150 °C) to avoid liquid sulfur physically deactivating the catalyst. To overcome this problem, the sub dew point Clauss reactors are oriented in parallel, with one operating and one spare. When one reactor has become saturated with adsorbed sulfur, the process flow is diverted to the standby reactor. The reactor is then regenerated by sending process gas that has been heated to 300–350 °C to vaporize the sulfur. This stream is sent to a condenser to recover the sulfur.

---

Process performance

Over 2.6 tons of steam will be generated for each ton of sulfur yield.

The physical properties of elemental sulfur obtained in the Claus process can differ from that obtained by other processes. In the Claus process, sulfur is usually transported as a liquid (melting point 115 °C). In elemental sulfur, viscosity increases rapidly at temperatures in excess of 160 °C due to the formation of polymeric sulfur chains.

Another anomaly is the solubility of residual H₂S in liquid sulfur as a function of temperature. Ordinarily, the solubility of a gas decreases with increasing temperature but H₂S behaves inversely Solubility of Hydrogen Sulfide in Sulfur Rocco Fanelli. Industrial & Engineering Chemistry 1949 41 (9), 2031-2033 DOI: 10.1021/ie50477a047. This means that toxic and explosive H₂S gas can build up in the headspace of any cooling liquid sulfur reservoir. The explanation for this anomaly is the endothermic reaction of sulfur with H₂S to polysulfanes H₂S_x.

---

Sulfur stockpile

Millions of tons of elemental sulfur are produced worldwide by the Claus process each year.

Owing to the high sulfur content of the Athabasca Oil Sands, stockpiles of elemental sulfur from this process now exist throughout Alberta, Canada.

(1982). 9780841207134 ISBN 9780841207134

Another way of storing sulfur, while reusing it as a valuable material, is as a binder for concrete, the resulting product having many desirable properties (see sulfur concrete).

---

See also

• Amine treating
• Hydro-desulfurization
• Crystasulf
• Hydrogenation
• Acid gas
• Sour gas

Post Comment